Световой барьер безопасности Omron F3SJ-B
Семейство F3SJ-B — это световые барьеры безопасности типа 4 с разрешающей способностью 25 мм. Ширина барьера достигает 7 м, высота варьируется в пределах от 185 до 2065 мм, мертвая зона отсутствует.
- Высота барьера = длина датчика
- Простая защита кистей рук
- Функция селективного пропуска
- Последовательное соединение до трех барьеров
- Датчик типа 4 в соответствии со стандартом EN 61496-1, уровень эффективности (PL) вплоть до «e» согласно EN ISO 13849
Заказная информация
| Application | Detection capability | Beam gap | Operating range | Protective height (mm) | Order code |
|---|---|---|---|---|---|
| Hand protection | Dia. 25 mm | 20 mm | 0.2 to 7 m | 185 to 2,065 | F3SJ-B____P25 |
| Number of beams | Protective height (mm) | Order code |
|---|---|---|
| 8 | 185 | F3SJ-B0185P25 |
| 10 | 225 | F3SJ-B0225P25 |
| 14 | 305 | F3SJ-B0305P25 |
| 18 | 385 | F3SJ-B0385P25 |
| 22 | 465 | F3SJ-B0465P25 |
| 26 | 545 | F3SJ-B0545P25 |
| 30 | 625 | F3SJ-B0625P25 |
| 34 | 705 | F3SJ-B0705P25 |
| 38 | 785 | F3SJ-B0785P25 |
| 42 | 865 | F3SJ-B0865P25 |
| 46 | 945 | F3SJ-B0945P25 |
| 50 | 1,025 | F3SJ-B1025P25 |
| 54 | 1,105 | F3SJ-B1105P25 |
| 58 | 1,185 | F3SJ-B1185P25 |
| 62 | 1,265 | F3SJ-B1265P25 |
| 66 | 1,345 | F3SJ-B1345P25 |
| 70 | 1,425 | F3SJ-B1425P25 |
| 74 | 1,505 | F3SJ-B1505P25 |
| 78 | 1,585 | F3SJ-B1585P25 |
| 82 | 1,665 | F3SJ-B1665P25 |
| 86 | 1,745 | F3SJ-B1745P25 |
| 90 | 1,825 | F3SJ-B1825P25 |
| 94 | 1,905 | F3SJ-B1905P25 |
| 98 | 1,985 | F3SJ-B1985P25 |
| 102 | 2,065 | F3SJ-B2065P25 |
Аксессуары (заказываются отдельно)
Single-end connector cable (2 cables per set, for emitter and receiver)
For wiring with safety circuit such as single safety relay, safety relay unit, and safety controller.
| Appearance | Cable length | Specifications | Order code |
|---|---|---|---|
 |
3 m | M12 connector (8-pin) | F39-JD3A |
| 7 m | F39-JD7A | ||
| 10 m | F39-JD10A | ||
| 15 m | F39-JD15A | ||
| 20 m | F39-JD20A |
Sensor mounting bracket
| Appearance | Specifications | Application | Remarks | Order code |
|---|---|---|---|---|
 |
Top/bottom bracket | Top/bottom bracket for F3SJ-E/B | 2 for an emitter, 2 for a receiver, total of 4 per set |
F39-LJB1 |
 |
Intermediate bracket | In combination use with top/bottom bracket for F3SJ-E/B Can be used as free-location bracket. |
1 set with 2 pieces | F39-LJB2 |
 |
Quick mount bracket | Quick mount bracket for F3SJ-E/B Supports M6 slide nut for aluminum frame. |
1 set with 2 pieces | F39-LJB3-M6 |
| Quick mount bracket for F3SJ-E/B Supports M8 slide nut for aluminum frame. |
F39-LJB3-M8 | |||
 |
Quick mount M6 bracket Quick mount M8 bracket |
Bracket to mount an intermediate bracket to the aluminum frame with a single touch. |
Hexagon socket head cap screws (M6 × 10) are included. |
F39-LJB3-M6K |
| Hexagon socket head cap screws (M8 × 14) are included. |
F39-LJB3-M8K | |||
 |
Compatible mounting bracket | Mounting bracket used when replacing existing area sensors (F3SJ-A or F3SN) with the F3SJ-E/B. |
2 for an emitter, 2 for a receiver, total of 4 per set |
F39-LJB4 |
 |
Contact mount bracket | Bracket to closely contact the back side of the sensor. | 2 for an emitter, 2 for a receiver, total of 4 per set |
F39-LJB5 |
Laser pointer
| Appearance | Output | Order code |
|---|---|---|
 |
Laser pointer for F3SJ | F39-PTJ |
Характеристики
| Model | F3SJ-B____P25 | ||
|---|---|---|---|
| Sensor type | Type 4 safety light curtain | ||
| Setting tool connection | Parameter settings: Not available | ||
| Safety category | Safety purpose of category 4, 3, 2, 1, or B | ||
| Detection capability | Opaque objects 25 mm in diameter | ||
| Beam gap (P) | 20 mm | ||
| Number of beams (n) | 8 to 102 | ||
| Protective height (PH) | 185 to 2,065 mm | ||
| Lens diameter | Diameter 5 mm | ||
| Operating range | 0.2 to 7 m | ||
| Response time (under stable light incident condition) | ON to OFF | 15 ms max. (response time at 1 set connection, series connection of 2 sets or 3 sets) | |
| OFF to ON | 70 ms max. (response time at 1 set connection, series connection of 2 sets or 3 sets) | ||
| Startup waiting time | 2 s max. | ||
| Power supply voltage (Vs) | SELV/PELV 24 VDC±20% (ripple p-p 10% max.) | ||
| Consumption current (no load) | Emitter: Up to 22 beams: 52 mA max., 26 to 42 beams: 68 mA max., 46 to 62 beams: 75 mA max., 66 to 82 beams: 88 mA max., 86 to 102 beams: 101 mA max. Receiver: Up to 22 beams: 45 mA max., 26 to 42 beams: 50 mA max., 46 to 62 beams: 56 mA max., 66 to 82 beams: 61 mA max., 86 to 102 beams: 67 mA max. |
||
| Light source (emitted wavelength) | Infrared LED (870 nm) | ||
| Effective aperture angle (EAA) | Based on IEC 61496-2. Within ±2.5° for both emitter and receiver when the detection distance is 3 m or over | ||
| Safety outputs (OSSD) | Two PNP transistor outputs, load current 200 mA max., residual voltage 2 V max. (except for voltage drop due to cable extension), Leakage current 1 mA max., load inductance 2.2 H max., Maximum capacity load 1 μF | ||
| Auxiliary output 1 | One PNP transistor outputs, load current 100 mA max., residual voltage 2 V max. (except for voltage drop due to cable extension), leak current 1 mA max. | ||
| Output operation mode | Safety output: On when receiving light Auxiliary output: - Reverse output of safety output for a basic system - ON when muting/override for a muting system |
||
| Input voltage | ON voltage: Vs-3 V to Vs, OFF voltage: 0 V to 1/2 Vs or open | ||
| Mutual interference prevention function | Mutual interference prevention algorithm prevents interference in up to 3 sets. | ||
| Series connection | Time division emission by series connection Number of connections: up to 3 sets (between F3SJ-Bs only)Other models cannot be connected. Total number of beams: up to 192 beams Maximum cable length for 2 sets: no longer than 7 m |
||
| Test function | Self test (at power-ON and at power distribution) External test (emission stop function by test input) |
||
| Safety-related functions | Interlock (basic system) External device monitoring (basic system) Muting (muting system) Override (muting system) |
||
| Connection type | Connector method (M12, 8-pin) | ||
| Protection circuit | Output short-circuit protection, and power supply reverse polarity protection | ||
| Ambient temperature | Operating: -10 to 55°C (non-freezing), Storage: -25 to 70°C | ||
| Ambient humidity | Operating: 35% to 85% (no condensation), Storage: 35% to 95% RH | ||
| Operating ambient light intensity | Incandescent lamp: 3,000 lx max., Sunlight: 10,000 lx max. | ||
| Insulation resistance | 20 MΩ min. (at 500 VDC) | ||
| Dielectric strength | 1,000 VAC 50/60 Hz, 1 min | ||
| Degree of protection | IP65 (IEC 60529) | ||
| Vibration resistance | Malfunction: 10 to 55 Hz, Multiple amplitude of 0.7 mm, 20 sweeps in X, Y, and Z directions | ||
| Shock resistance | Malfunction: 100 m/s2, 1,000 times each in X, Y, and Z directions | ||
| Pollution degree | Pollution degree 3 (IEC 60664-1) | ||
| Power cable | Connection method: Prewired connector cable, cable length 0.3 m, connector type (M12, 8-pin), connector: IP67 rated (when mated) Number of wires: 8 wires Cable diameter: Dia. 6 mm Allowable bending radius: R5 mm |
||
| Extension cable | 30 m max. | ||
| Material | Case: Aluminum Cap: ABS resin, PBT Optical cover: PMMA resin (acrylic) Cable: Oil resistant PVC |
||
| Weight (packed state) | Weight (g) = (protective height) × 2.7 + 500 | ||
| Accessories | Test rod, Instruction manual, User's manual (CD-ROM) | ||
| Applicable standards | IEC 61496-1, EN 61496-1 UL 61496-1, Type 4 ESPE (Electro-sensitive protective equipment) IEC 61496-2, CLC/TS 61496-2, UL 61496-2, Type 4 AOPD (Active opto-electronic protective devices) IEC 61508-1 to -3, EN 61508-1 to -3 SIL3 IEC 13849-1: 2006, EN ISO 13849-1: 2008 (PLe, Cat.4) UL 508, UL 1998, CAN/CSA C22.2 No.14, CAN/CSA C22.2 No.0.8 |
||
