Корзина пуста
Измерительные датчики Omron ZX-GT
Новый интеллектуальный лазерный микрометр ZX-GT функционально расширяет платформу микропроцессорных лазерных измерительных датчиков компании Omron. ZX-GT способен обнаруживать края, измерять диаметр объектов, с высочайшей точностью вычислять положение объектов из любых материалов. Выполненный на базе технологии ПЗС, датчик ZX-GT обеспечивает высокую точность и скорость измерений даже при неблагоприятных условиях эксплуатации. Прозрачность объектов, наличие отражений от поверхности, изменение положения не оказывают влияния на результат измерения. Лазерный микрометр можно легко настроить и сконфигурировать на ПК с помощью программы Smart Monitor.
- Высокая точность: 5–10 мкм
- Любые поверхности
- Большое расстояние до объекта измерения: до 500 мм
- Ширина линии (луча) до 28 мм
- Вычислительный блок для нескольких головок
Заказная информация
Sensors
Type | Optical system | Measuring width | Sensing distance | Resolution | Output type | Order code |
---|---|---|---|---|---|---|
Separate type | Through-beam | 28 mm | 0 to 500 mm | 10 µm | NPN | ZX-GT28S11 |
PNP | ZX-GT28S41 | |||||
Integrated type | 40 mm | NPN | ZX-GT2840S11 | |||
PNP | ZX-GT2840S41 |
Controller
Power supply | Output type | Order code |
---|---|---|
DC | NPN | ZX-GTC11 |
PNP | ZX-GTC41 |
Accessories (order separately)
Set of interface unit and setup software PCs
Output type | Order code |
---|---|
NPN | ZX-GIF11A |
PNP | ZX-GIF41A |
Interface unit(RS-232C/binary output)
Power supply | Output type | Order code |
---|---|---|
DC | NPN | ZX-GIF11 |
PNP | ZX-GIF41 |
Setup software PCs
Name | Order code |
---|---|
Smart monitor GT | ZX-GSW11 |
Calculating units
Order code | |
---|---|
Calculating unit | ZX-CAL2 |
Receiver-controller extension cable
Cable length | Quantity | Order code | |
---|---|---|---|
Standard cable | Flexible cable | ||
1 m | 1 m | ZX-XGC1A | ZX-XGC1R |
2 m | ZX-XGC2A | ZX-XGC2R | |
5 m | ZX-XGC5A | ZX-XGC5R | |
8 m | ZX-XGC8A | ZX-XGC8R | |
20 m | ZX-XGC20A | ZX-XGC20R | |
Up to two extension cables can be connected. However, be sure to limit the total extension cable length between the receiver and the controller to 30 meters (including the receiver cable). |
Sensor
Item | ZX-GT28S11 | ZX-GT2840S11 | ZX-GT28S41 | ZX-GT2840S41 |
---|---|---|---|---|
Output type | NPN | PNP | ||
Appearance | Separate type | Integrated type | Separate type | Integrated type |
Light source | Visible semiconductor laser diode (wavelength 650 nm, CLASS 1 of EN60825-1/IEC60825-1, CLASS of FDA(21CFR 1040.10 and 1040.11) | |||
Measuring width | 28 mm | |||
Sensing distance | 0 to 500 mm | 40 mm | 0 to 500 mm | 40 mm |
Minimum sensing object | 0.5 mm dia. | 0.2 mm dia. | 0.5 mm dia. | 0.2 mm dia. |
Linearity | ±0.1% F.S. | |||
Resolution | 10 µm (number of process values to average: 16) | |||
Temperature characteristic | ±0.01% F.S/C | |||
Indicators (emitter) | Laser ON indicator (green), laser alarm indicator (red) | |||
Indicator (receiver) | Optical axis setting indicator (green) | |||
Laser OFF input/sync input | ON: Short-circuited with 0 V or 1.5 V max. OFF: Open (leakage current: 0.1 mA max.) |
ON: Short-circuited with power supply voltage or power supply voltage -1.5 V max. OFF: Open (leakage current: 0.1 mA max.) |
||
Laser deterioration alarm output | NPN open-collector output 30 VDC 20 mA max. Residual voltage 1.2 V max. |
PNP open-collector output 30 VDC 20 mA max. Residual voltage 2 V max. |
||
Power consumption (emitter) | 30 mA max. | |||
Power supply voltage (emitter) | 24 VDC+10%, -15% ripple (p-p) 10% max. | |||
Dielectric strength | 1,000 VAC, 50/60 Hz for 1 min | |||
Insulation resistance | 20 M Ω(at 500 VDC megger) | |||
Operating ambient illumination (emitter) |
3,000 lx (incandescent light) | |||
Operating ambient illumination (receiver) |
1,000 lx (incandescent light) | |||
Ambient temperature | Operating: 0 to 40°C, storage: -15 to 50°C (with no icing or condensation) | |||
Ambient humidity | Operating and storage: 35% to 85% (with no condensation) | |||
Vibration resistance (durability) | 10 to 150 Hz single-amplitude: 0.75 mm for 80 min each in X, Y and Z directions | |||
Degree of protection | IEC60529 IP40 | |||
Cable length | 2 m | |||
Material | Case: aluminum die-cast, Lens: glass | |||
Weight (packed state) | Approx. 550 g | Approx. 570 g | Approx. 550 g | Approx. 570 g |
Accessories | Laser warning labels, instruction sheet | |||
F.S.: 28 mm measuring range of receiver |
Controller
Item | ZX-GTC11 | ZX-GTC41 | |
---|---|---|---|
Output type | NPN | PNP | |
Measurement cycle | 1.5 ms (standard mode (NORM)) 0.5 ms (high-speed mode (FAST)) |
||
Samples to average | 1/2/4/8/16/32/64/128/256/512/1024/2048/4096 | ||
Analog output | For current output: 4 to 20 mA/F.S., max. load resistance 300 Ω For voltage output: ±4 V, (±5 V, 1 to 5 V), output impedance 100 Ω |
||
Timing input, bank switching input, zero reset input, reset input | ON: short-circuited with 0 V or 1.5 V max. OFF: Open (leakage current: 0.1 mA max.) |
ON: short-circuited with power supply voltage or power supply voltage -1.5 V max. OFF: Open (leakage current: 0.1 mA max.) |
|
HIGH/PASS/LOW Judgment output Sync output |
NPN open-collector output 30 VDC 50 mA max. Residual voltage 1.2 V max. |
PNP open-collector output 30 VDC 50 mA max. Residual voltage 2 V max. |
|
Indicator | Judgment output indicator: HIGH (orange), PASS (green), LOW (orange) Main display (red) sub-display (yellow) bank 1/2 (orange), zero reset (green) |
||
Main functions | Number of registered setups |
2 banks | |
Measurement mode | Interrupted beam width measurement, incident beam width measurement, outer diameter measurement, center position measurement, IC lead pitch, IC lead width judgment, specified edge measurement, wire position measurement, glass edge position measurement |
||
Display during measurement | Measured value, resolution, threshold, voltage output value, current output value (number of display digits can be changed) | ||
Zero reset functions | Offset setting of zero reset value, zero reset value memory | ||
Hold | Sample hold, peak hold, bottom hold, peak-to-peak hold, average hold, delay hold | ||
Timer functions | ON-delay, OFF-delay, one-shot | ||
Adjustment functions | Optical axis adjust mode/light intensityt writing mode, variable binary level, variable edge filter, analog output scaling | ||
Calculation | 2 possible on up to two controllers (calculation Unit ZX-CAL2 is required for connecting controllers to each other.) A-B, A+B, width | ||
Other | Measurement cycle setting, threshold setting, hysteresis setting, initialization, key lock | ||
Temperature characteristic | ±0.005% F.S./°C | ||
Current consumption | 150 mA max. (including receiver) | ||
Power supply voltage | 24 VDC+10%, -15% ripple (p-p) 10% max. | ||
Dielectric strength | 1,000 VAC, 50/60 Hz for min | ||
Insulation resistance | 20 MΩ(at 500 VDC megger) | ||
Ambient temperature | Operating: 0 to 50°C, storage: -15 to 60°C (with no icing or condensation) | ||
Ambient humidity | Operating and storage: 35% to 85% (with no condensation) | ||
Vibration resistance(durability) | 10 to 150 Hz single-amplitude: 0.35 mm for 80 min each in X, Y and Z directions | ||
Degree of protection | IEC60529 IP20 | ||
Cable length | 2 m | ||
Material | Case: PBT (polybutylene terephthalate), cover: Polycarbonate | ||
Weight (packed state) | Approx. 330 g | ||
Accessories | Instruction sheet |
Interface unit
Item | ZX-GIF11/-GIF11A | ZX-GIF41/-GIF41A |
---|---|---|
Compatible controller | ZX-GTC11 | ZX-GTC41 |
Indicator | Power ON (green), controller communications (orange), controller communications error (red), RS-232C communications (orange), RS-232C communications error (red), binary output (orange) |
|
Communications port | RS-232C (9-pin D-sub connector) | |
12-bit binary output (D11 toD0, GATE) |
NPN open-collector output 30 VDC 20 mA max. Residual voltage 1.2 V max. |
PNP open-collector output 30 VDC 20 mA max. Residual voltage 2 V max. |
Power supply voltage | Supplied from controller (power consumption: 60 mA max.) | |
Dielectric strength | 1,000 VAC, 50/60 Hz for 1 min | |
Insulation resistance | 20 M Ω(at 500 VDC megger) | |
Ambient temperature | Operating: 0 to 50°C, storage: -15 to 60°C (with no icing or condensation) | |
Ambient humidity | Operating and storage: 35% to 85% (with no condensation) | |
Vibration resistance(durability) | 10 to 150 Hz single-amplitude: 0.35 mm for 80 min each in X, Y and Z directions | |
Degree of protection | IEC60529 IP20 | |
Cable length | RS-232C 0.5 m, binary output 2 m | |
Material | Case: PBT (polybutylene terephthalate), cover: Polycarbonate | |
Weight (packed state) | ZX-GIF_1A: Approx. 550 g ZX-GIF_1: Approx. 330 g |
|
Accessories | ZX-GIF_1A: Setup coftware (CD-ROM), 2 clamps, instruction sheet ZX-GIF_1: 2 clamps, instruction sheet |