Фильтры товаров Фильтры товаров

Измерительные датчики Omron ZX-GT

Omron ZX-GT

Новый интеллектуальный лазерный микрометр ZX-GT функционально расширяет платформу микропроцессорных лазерных измерительных датчиков компании Omron. ZX-GT способен обнаруживать края, измерять диаметр объектов, с высочайшей точностью вычислять положение объектов из любых материалов. Выполненный на базе технологии ПЗС, датчик ZX-GT обеспечивает высокую точность и скорость измерений даже при неблагоприятных условиях эксплуатации. Прозрачность объектов, наличие отражений от поверхности, изменение положения не оказывают влияния на результат измерения. Лазерный микрометр можно легко настроить и сконфигурировать на ПК с помощью программы Smart Monitor.

  • Высокая точность: 5–10 мкм
  • Любые поверхности
  • Большое расстояние до объекта измерения: до 500 мм
  • Ширина линии (луча) до 28 мм
  • Вычислительный блок для нескольких головок

Заказная информация

Sensors

Type Optical system Measuring width Sensing distance Resolution Output type Order code
Separate type Through-beam 28 mm 0 to 500 mm 10 µm NPN ZX-GT28S11
PNP ZX-GT28S41
Integrated type 40 mm NPN ZX-GT2840S11
PNP ZX-GT2840S41

Controller

Power supply Output type Order code
DC NPN ZX-GTC11
PNP ZX-GTC41

Accessories (order separately)

Set of interface unit and setup software PCs

Output type Order code
NPN ZX-GIF11A
PNP ZX-GIF41A

Interface unit(RS-232C/binary output)

Power supply Output type Order code
DC NPN ZX-GIF11
PNP ZX-GIF41

Setup software PCs

Name Order code
Smart monitor GT ZX-GSW11

Calculating units

Order code
Calculating unit ZX-CAL2

Receiver-controller extension cable

Cable length Quantity Order code
Standard cable Flexible cable
1 m 1 m ZX-XGC1A ZX-XGC1R
2 m ZX-XGC2A ZX-XGC2R
5 m ZX-XGC5A ZX-XGC5R
8 m ZX-XGC8A ZX-XGC8R
20 m ZX-XGC20A ZX-XGC20R
Up to two extension cables can be connected. However, be sure to limit the total extension cable length between the receiver and the controller to 30 meters (including the receiver cable).

Sensor

Item ZX-GT28S11 ZX-GT2840S11 ZX-GT28S41 ZX-GT2840S41
Output type NPN PNP
Appearance Separate type Integrated type Separate type Integrated type
Light source Visible semiconductor laser diode (wavelength 650 nm, CLASS 1 of EN60825-1/IEC60825-1, CLASS of FDA(21CFR 1040.10 and 1040.11)
Measuring width 28 mm
Sensing distance 0 to 500 mm 40 mm 0 to 500 mm 40 mm
Minimum sensing object 0.5 mm dia. 0.2 mm dia. 0.5 mm dia. 0.2 mm dia.
Linearity ±0.1% F.S.
Resolution 10 µm (number of process values to average: 16)
Temperature characteristic ±0.01% F.S/C
Indicators (emitter) Laser ON indicator (green), laser alarm indicator (red)
Indicator (receiver) Optical axis setting indicator (green)
Laser OFF input/sync input ON: Short-circuited with 0 V or 1.5 V max.
OFF: Open (leakage current: 0.1 mA max.)
ON: Short-circuited with power supply voltage or
power supply voltage -1.5 V max.
OFF: Open (leakage current: 0.1 mA max.)
Laser deterioration alarm output NPN open-collector output
30 VDC 20 mA max.
Residual voltage 1.2 V max.
PNP open-collector output
30 VDC 20 mA max.
Residual voltage 2 V max.
Power consumption (emitter) 30 mA max.
Power supply voltage (emitter) 24 VDC+10%, -15% ripple (p-p) 10% max.
Dielectric strength 1,000 VAC, 50/60 Hz for 1 min
Insulation resistance 20 M Ω(at 500 VDC megger)
Operating ambient illumination
(emitter)
3,000 lx (incandescent light)
Operating ambient illumination
(receiver)
1,000 lx (incandescent light)
Ambient temperature Operating: 0 to 40°C, storage: -15 to 50°C (with no icing or condensation)
Ambient humidity Operating and storage: 35% to 85% (with no condensation)
Vibration resistance (durability) 10 to 150 Hz single-amplitude: 0.75 mm for 80 min each in X, Y and Z directions
Degree of protection IEC60529 IP40
Cable length 2 m
Material Case: aluminum die-cast, Lens: glass
Weight (packed state) Approx. 550 g Approx. 570 g Approx. 550 g Approx. 570 g
Accessories Laser warning labels, instruction sheet
F.S.: 28 mm measuring range of receiver

Controller

Item ZX-GTC11 ZX-GTC41
Output type NPN PNP
Measurement cycle 1.5 ms (standard mode (NORM))
0.5 ms (high-speed mode (FAST))
Samples to average 1/2/4/8/16/32/64/128/256/512/1024/2048/4096
Analog output For current output: 4 to 20 mA/F.S., max. load resistance 300 Ω
For voltage output: ±4 V, (±5 V, 1 to 5 V), output impedance 100 Ω
Timing input, bank switching input, zero reset input, reset input ON: short-circuited with 0 V or 1.5 V max.
OFF: Open (leakage current: 0.1 mA max.)
ON: short-circuited with power supply voltage or
power supply voltage -1.5 V max.
OFF: Open (leakage current: 0.1 mA max.)
HIGH/PASS/LOW
Judgment output
Sync output
NPN open-collector output
30 VDC 50 mA max.
Residual voltage 1.2 V max.
PNP open-collector output
30 VDC 50 mA max.
Residual voltage 2 V max.
Indicator Judgment output indicator: HIGH (orange), PASS (green), LOW (orange)
Main display (red) sub-display (yellow) bank 1/2 (orange), zero reset (green)
Main functions Number of registered
setups
2 banks
Measurement mode Interrupted beam width measurement, incident beam width measurement, outer diameter measurement, center position measurement, IC lead pitch,
IC lead width judgment, specified edge measurement, wire position measurement, glass edge position measurement
Display during measurement Measured value, resolution, threshold, voltage output value, current output value (number of display digits can be changed)
Zero reset functions Offset setting of zero reset value, zero reset value memory
Hold Sample hold, peak hold, bottom hold, peak-to-peak hold, average hold, delay hold
Timer functions ON-delay, OFF-delay, one-shot
Adjustment functions Optical axis adjust mode/light intensityt writing mode, variable binary level, variable edge filter, analog output scaling
Calculation 2 possible on up to two controllers (calculation Unit ZX-CAL2 is required for connecting controllers to each other.) A-B, A+B, width
Other Measurement cycle setting, threshold setting, hysteresis setting, initialization, key lock
Temperature characteristic ±0.005% F.S./°C
Current consumption 150 mA max. (including receiver)
Power supply voltage 24 VDC+10%, -15% ripple (p-p) 10% max.
Dielectric strength 1,000 VAC, 50/60 Hz for min
Insulation resistance 20 MΩ(at 500 VDC megger)
Ambient temperature Operating: 0 to 50°C, storage: -15 to 60°C (with no icing or condensation)
Ambient humidity Operating and storage: 35% to 85% (with no condensation)
Vibration resistance(durability) 10 to 150 Hz single-amplitude: 0.35 mm for 80 min each in X, Y and Z directions
Degree of protection IEC60529 IP20
Cable length 2 m
Material Case: PBT (polybutylene terephthalate), cover: Polycarbonate
Weight (packed state) Approx. 330 g
Accessories Instruction sheet

Interface unit

Item ZX-GIF11/-GIF11A ZX-GIF41/-GIF41A
Compatible controller ZX-GTC11 ZX-GTC41
Indicator Power ON (green), controller communications (orange), controller communications error (red), RS-232C communications (orange),
RS-232C communications error (red), binary output (orange)
Communications port RS-232C (9-pin D-sub connector)
12-bit binary output
(D11 toD0, GATE)
NPN open-collector output
30 VDC 20 mA max.
Residual voltage 1.2 V max.
PNP open-collector output
30 VDC 20 mA max.
Residual voltage 2 V max.
Power supply voltage Supplied from controller (power consumption: 60 mA max.)
Dielectric strength 1,000 VAC, 50/60 Hz for 1 min
Insulation resistance 20 M Ω(at 500 VDC megger)
Ambient temperature Operating: 0 to 50°C, storage: -15 to 60°C (with no icing or condensation)
Ambient humidity Operating and storage: 35% to 85% (with no condensation)
Vibration resistance(durability) 10 to 150 Hz single-amplitude: 0.35 mm for 80 min each in X, Y and Z directions
Degree of protection IEC60529 IP20
Cable length RS-232C 0.5 m, binary output 2 m
Material Case: PBT (polybutylene terephthalate), cover: Polycarbonate
Weight (packed state) ZX-GIF_1A: Approx. 550 g
ZX-GIF_1: Approx. 330 g
Accessories ZX-GIF_1A: Setup coftware (CD-ROM), 2 clamps, instruction sheet
ZX-GIF_1: 2 clamps, instruction sheet
Развернуть полное описание
ZX-GT2840S11
238018
172 415.00 Рруб.172415.000000
измерительная головка, 28mm диапазон измерения, интегрированный тип 40mm, NPN выход ошибки лазера
+

ZX-GT2840S41
238019
172 415.00 Рруб.172415.000000
измерительная головка, 28mm диапазон измерения, интегрированный тип 40mm, PNP выход ошибки лазера
+

ZX-GT28S11
238016
168 102.00 Рруб.168102.000000
измерительная головка, 28mm диапазон измерения, separated type 0 to 500mm, NPN выход ошибки лазера
+

ZX-GT28S41
238017
168 102.00 Рруб.168102.000000
измерительная головка, 28mm диапазон измерения, separated type 0 to 500mm, PNP выход ошибки лазера
+

ZX-GTC11
238014
51 855.00 Рруб.51855.000000
контроллер, NPN output
+

ZX-GTC41
238015
51 855.00 Рруб.51855.000000
контроллер, PNP output
+